• Home
  • 70×140 Steel Building: Manufacturing Shop in Duncan, BC

70×140 Steel Building: Manufacturing Shop in Duncan, BC

Structural Engineer

Published

21 Nov 2026 · 5 minutes Read

#1 Metal Buildings in Ohio | Toro Buildings Dream Shop – Thrive Base
70x140Clear-span steel building, in feet
9,800Square feet, plus a mezzanine
25 ftEave height, crane-ready
Sa 1.10Seismic spectral response, Vancouver Island

What does a 70x140 steel building look like as a manufacturing shop? This one is a 9,800 sq ft red iron shop in Duncan, British Columbia, 70 ft wide, 140 ft long and 25 ft to the eave, with a 5-ton underhung crane, a 70 x 20 ft concrete mezzanine and a 20 x 60 ft side canopy, engineered for Vancouver Island's high seismic loads. Toro designed, engineered and supplied this 70x140 steel building for a local HVAC and sheet metal fabrication business in the Cowichan Valley.

It is a pre-engineered red iron steel building with tapered clear-span frames, the system our customers choose for manufacturing facilities, shops and commercial buildings. Toro has supplied pre-engineered steel buildings for more than 40 years and sold more than 100,000 of them, and every one is engineered for the snow, wind and seismic loads at its exact site. This 70x140 steel building shipped with drawings sealed by an engineer licensed in British Columbia and was assembled locally on the owner's foundation.

Key takeaways

  • Engineered for Cascadia. Designed for Vancouver Island's high seismic loads, with Sa(0.2) = 1.10 on stiff soil.
  • Crane, mezzanine and canopy in one design. A 5-ton underhung crane, a 70 x 20 ft concrete mezzanine and a 20 x 60 ft open side canopy.
  • Built for a working shop. Four 12 x 14 ft door openings, full-height steel liner panels and a 25 ft eave.

70x140 steel building specs

The 70x140 steel building as ordered and engineered.

Detail70x140 Steel Building: Manufacturing Shop
LocationDuncan, Cowichan Valley, Vancouver Island, British Columbia, Canada
BuildingPre-engineered red iron steel building with tapered clear-span frames
Size70 ft wide x 140 ft long
Eave height25 ft
Floor area9,800 sq ft, plus a 1,400 sq ft mezzanine
Roof1:12 gable, 24-gauge standing seam
BaysSeven 20 ft bays
Crane5-ton underhung crane, single girder, pendant control
Mezzanine70 x 20 ft, 13 ft high, concrete deck
Side canopy20 x 60 ft lean-to, open on three sides
DoorsFour 12 x 14 ft framed openings, two insulated wind-rated walk doors and a third walk door opening
WindowsThree 3 x 3 ft and four 6 x 3 ft window openings at 16 ft
Walls24-gauge PBR, full-height steel liner panels, 2 ft masonry base
Insulation6 in. roof, 6 in. walls (installed locally)
Code2010 National Building Code of Canada, the basis of the BC Building Code at the time
OrderedDecember 2018

Price a building like this

Tell us your size, site and use, and a Toro building consultant will come back with an engineered, code-compliant quote.

Watch: from sealed drawings to finished manufacturing shop

This 70x140 steel building went from sealed engineering drawings to a finished manufacturing shop in Duncan, on Vancouver Island. Watch the whole sequence, then see photos of the building below.

This 70x140 steel manufacturing building in Duncan, BC, from sealed engineering drawings to the finished shop with its side canopy.

70x140 steel building manufacturing shop in Duncan, BC with an overhead door and side canopy
The finished shop, with an overhead door on the sidewall and the side canopy at the far end.
Steel side canopy along the sidewall of a manufacturing building in Duncan, BC
The 20 x 60 ft side canopy, open on three sides, over a concrete apron.
Main entrance of a dark steel manufacturing building with upper windows in Duncan, British Columbia
The main entrance, with upper windows lighting the mezzanine level.
Clear-span red iron frames of a 70x140 steel building going up in Duncan, BC
The clear-span frames going up, with no interior columns across the main floor.
Steel columns and girts of a steel building frame on Vancouver Island
Columns, girts and bracing before the wall panels went on.
Inside a steel manufacturing building before the slab pour, with white liner panels on the walls
Inside before the slab pour, with full-height white liner panels on the walls.

Design your own building the same way with the free 3D building designer: set the width, length, height, doors, lean-tos, roof pitch, colours and wainscot, then send it to a building consultant for an engineered price.

Want a building like this one?

Send us your size, site and how you will use it, and a building consultant will come back with an engineered quote.

Engineered for Duncan, BC: the design loads

Duncan sits in the Cowichan Valley on southern Vancouver Island, in one of Canada's highest seismic zones, with wet winters and moderate snow. These are the design criteria for this 70x140 steel building.

Design criteriaValue
Building code2010 National Building Code of Canada (NBC), the basis of the BC Building Code at the time. Drawings sealed by an engineer licensed in BC
SeismicHigh: Sa(0.2) = 1.10, Sa(0.5) = 0.74, Sa(1.0) = 0.37, Sa(2.0) = 0.183, site class D (stiff soil)
Ground snow load42.6 psf (2.04 kPa)
Roof snow load (design)42.5 psf (2.04 kPa), normal exposure
Rain load8.4 psf (0.40 kPa), rain intensity 8 mm in 15 min
Roof live load20.9 psf (1.0 kPa)
Wind1-in-50-year wind pressure of 8.15 psf (0.39 kPa), open terrain
ImportanceNormal (importance factors 1.0 for snow, wind and seismic)
Collateral load4.5 psf
Crane5-ton underhung, Class C, crane sidesway limit H/100
MezzanineLive load 50 psf, partitions 20 psf, 4 in. concrete deck
Drawings suppliedSealed anchor rod plan with reactions, sealed permit and erection drawings, and a sealed letter of certification with calculations

See how we engineer every building on our engineering page, or read about the BC Building Code. More from Noah Sinclair, our in-house structural engineer.

Get loads engineered for your site

Every quote is engineered for the snow, wind and seismic loads where your building will stand.

Engineering a 70x140 steel building for Vancouver Island earthquakes

Seismic design drives the frames on the coast.

Southern Vancouver Island sits near the Cascadia subduction zone, and its seismic design values are among the highest in Canada. This building was designed for a short-period spectral response of 1.10 on stiff soil, many times what a building in Ontario or the prairies sees.

  • Heavier frames and connections sized for earthquake forces, not just snow and wind.
  • Rod bracing in the roof and both sidewalls, with braced bays matched to the crane and mezzanine loads.
  • A seismic sidesway limit checked alongside the crane limit, so the runway stays aligned.
  • The mezzanine and its concrete deck included in the seismic design, since heavy floors add mass the frames must resist.

Steel performs well in earthquakes because it bends before it breaks. The engineering makes sure the frames, bracing and anchor rods carry the forces down to a foundation designed for them.

On the coast, earthquakes often govern the design. The frames, bracing and anchor rods are sized for them first.
Toro engineering, on Vancouver Island buildings

The crane, mezzanine and side canopy

Three features engineered into one 70x140 steel building.

  • A 5-ton underhung crane, single girder with pendant control, running along the building with about 59 ft between rails and over 17 ft of clearance under the runway beams. Runway beams came with the building; end stops and the crane itself came from the crane supplier.
  • A 70 x 20 ft mezzanine across one end bay, 13 ft high with a 4 in. concrete deck on steel deck and joists, designed for 50 psf live load plus 20 psf for partitions. Two interior columns on that frame line carry it.
  • A 20 x 60 ft side canopy, a lean-to attached to the sidewall and open on three sides, giving covered space for loading and storing material out of the rain.

Planning a crane or mezzanine? Share the crane data and the loads you need before the order is finalized, because the frames and foundation are engineered from them. See how we handled two 5-ton cranes on our 80x100 welding shop in Thunder Bay and a ramp mezzanine on our 50x50 skate park in Colorado.

Walls, liners and openings for a working shop

An envelope that stands up to fabrication work.

  • 24-gauge PBR wall panels, a heavier gauge than many standard buildings.
  • Full-height 24-gauge steel liner panels on the walls in white, which protect the insulation and brighten the shop. They were specified as part of a fire-rated wall assembly, with the final assembly approved by the local building official.
  • A 2 ft masonry base along the walls, where forklifts and carts are most likely to hit.
  • A 24-gauge standing seam roof on high sliding clips with thermal blocks, over 6 in. of roof insulation.
  • Four 12 x 14 ft door openings for trucks and material, plus insulated, wind-rated walk doors.
  • Seven window openings at 16 ft, lighting the mezzanine level and the shop floor.
  • Northern-style gutters with 25 ft downspouts for coastal rain.

What to watch for when building on Vancouver Island

The issues that matter most in the Cowichan Valley.

  • Seismic loads. They often govern the design on the coast, so give your building specialist the exact site address early.
  • Soil conditions. Seismic design depends on the site class, so a geotechnical report helps the engineer and the foundation designer.
  • Rain and moisture. Wet winters call for good gutters, sealed openings and a plan for condensation in a heated shop.
  • Ferry logistics. Freight crosses to the island by ferry, so plan delivery dates and truck access to the site.
  • Permits. Depending on where the site is, the permit comes from the City of Duncan, the Municipality of North Cowichan or the Cowichan Valley Regional District. Check which one applies before you order.
  • Use and fire separation. Manufacturing buildings can need fire-rated walls or separations, so confirm the requirements with the building official early.

See our steel buildings in British Columbia page for more on BC codes and projects.

Give us the exact site address early. On Vancouver Island, the seismic numbers change with the site.
West Coast design note

Building in BC?

Get a quote engineered for your site's seismic, snow and wind loads, within 1 business day.

What does a 70x140 steel building cost?

Starting prices, and what moves them.

New Toro steel building kits start at $26 per sq ft (CAD) in Canada and $19 per sq ft (USD) in the United States, and every building is quoted to meet the loads and codes for your location and use. For a 70x140 steel building, the biggest price drivers are:

  • Seismic, snow and wind loads. High seismic zones need heavier framing and bracing.
  • Cranes. Runway beams, heavier frames and bracing add cost, and the crane is bought separately.
  • A mezzanine, sized for its loads and deck type.
  • Eave height. A 25 ft eave uses more steel than a standard 16 to 20 ft shop.
  • Liner panels, doors, windows and canopies.
  • Delivery, including ferry crossings for island sites.

The building kit doesn't include the foundation, erection, insulation, cranes or overhead doors, so budget for those separately. See our steel building sizes page and our Canadian steel building prices guide.

Need a building sooner, or for less?

New, unused clearance buildings from cancelled orders are engineered for your site like any Toro building.

Why manufacturers choose Toro for engineered steel buildings

More than 40 years and 100,000+ buildings.

  • More than 40 years supplying pre-engineered steel buildings, with more than 100,000 buildings sold.
  • In-house engineering, with every building designed for the snow, wind and seismic loads at its exact site and shipped with engineer-stamped drawings.
  • Cranes, mezzanines and canopies engineered in, not bolted on later.
  • Precision laser-cut components that arrive ready to bolt together, for 30 to 50% faster construction than conventional wood framing.
  • A 25 to 40-year paint warranty on straight-wall buildings, depending on panel and finish.
  • Canadian offices in Markham and Oshawa, with building specialists who speak English, French, Spanish, Portuguese, Italian, Persian and Chinese.

Start your quote

Tell us your size, site and use, and get a free quote engineered for your loads and code.

How this building came together

Toro engineers and supplies the kit; the owner's team builds it.

1

Specification and 3D design

Toro and the owner

Size, crane, mezzanine, canopy and openings set for a fabrication shop.

2

Engineering

Toro

The 70x140 steel building designed to the NBC for the Duncan site and sealed in BC.

3

Permit and foundation

Owner or contractor

Drawings submitted for permit; foundation built to the sealed reactions.

4

Delivery

Toro ships, the owner unloads

The complete kit trucked to Vancouver Island by ferry.

5

Assembly

Owner or contractor

Frames, crane beams, mezzanine and panels bolted together on site. Toro doesn't install.

The building consultant who sold this building

Every Toro building has one consultant from first call to delivery.

Nick Levy

Building Consultant · Toro Steel Buildings

Nick Levy sold this 70x140 steel building and worked with the owner through the crane, mezzanine, canopy and seismic requirements. He has been with Toro since 2002 and helps customers across Canada and the U.S. plan buildings from garages to large commercial and industrial shops.

See Nick's projects and work with Nick

789Buildings sold
24Years at Toro

More buildings Nick Levy has sold

Talk to Nick about your building

Get an engineered quote for your size, site and loads, ask about new and unlisted clearance inventory, or see Nick's past projects.

70x140 steel building FAQs

Still planning your build? Price your building and a building consultant will walk you through it.

How big is a 70x140 steel building?

A 70x140 steel building has 9,800 square feet of floor space. This one in Duncan, BC uses clear-span frames across most of its length, has a 25 ft eave height, and adds a 70 x 20 ft mezzanine and a 20 x 60 ft side canopy.

How much does a 70x140 steel building cost?

New Toro steel building kits start at $26 per sq ft (CAD) in Canada and $19 per sq ft (USD) in the United States, and every building is quoted to meet the loads and codes for your location and use. Seismic and snow loads, cranes, a mezzanine, eave height, doors and delivery have the biggest effect on the final price.

Can a steel building be designed for Vancouver Island earthquakes?

Yes. This Duncan building was engineered for a seismic spectral response of Sa(0.2) = 1.10 on stiff soil under the National Building Code of Canada, with heavier frames, rod bracing and anchor rods sized for earthquake forces. Every Toro building is engineered for its own site.

What snow load is a steel building designed for in Duncan, BC?

This building was designed for a ground snow load of 42.6 psf (2.04 kPa) and a roof snow load of 42.5 psf (2.04 kPa), plus a rain load of 8.4 psf. Your loads depend on your exact location and elevation.

Can a steel building have a crane and a mezzanine?

Yes, when both are engineered with the building. This 70x140 steel building has a 5-ton underhung crane and a 70 x 20 ft concrete mezzanine designed for 50 psf live load. Share your crane data and mezzanine loads before the order is finalized.

Do I need a building permit for a steel building in the Cowichan Valley?

Yes. Depending on the site, permits come from the City of Duncan, the Municipality of North Cowichan or the Cowichan Valley Regional District. Every Toro building comes with drawings sealed by an engineer licensed in BC, which is what building departments ask for.

What foundation does a 70x140 steel building need?

The foundation is designed locally for your soil, using the anchor rod plan and column reactions on the sealed drawings. On Vancouver Island, seismic loads and crane loads both affect the footings, so involve a foundation engineer early.

How long does it take to build a 70x140 steel building?

Delivery of a Toro building kit usually takes 2 to 8 weeks, and your building specialist confirms timing. The components arrive precision-cut and ready to bolt together, so construction is typically 30 to 50% faster than conventional wood framing.

Written by Noah Sinclair, Toro's in-house structural engineer. Every Toro building is engineered for your site's snow, wind and seismic loads and comes with engineer-stamped drawings. Toro has supplied pre-engineered steel buildings for more than 40 years and sold more than 100,000 buildings.

Follow Toro

Keep reading

Browse all articles

Planning a shop like this?

Toro Steel Buildings engineers your kit for your site's seismic, snow, wind and crane loads, with a quote within 1 business day.

Join 100,000+ customers who built with Toro

Tell us your size, location and how you'll use the building. A Toro building consultant will come back with an engineered, code-compliant quote within 1 business day. Prefer to talk? Call 1-888-995-3432, or browse in-stock clearance buildings at reduced prices.