• Home
  • Arctic Steel Building: 73×73 Insulated Storage in Gjoa Haven, Nunavut

Arctic Steel Building: 73×73 Insulated Storage in Gjoa Haven, Nunavut

Structural Engineer

Published

20 Nov 2026 · 5 minutes Read

#1 Metal Buildings in Ohio | Toro Buildings Dream Shop – Thrive Base
73x73Single-slope storage, in feet
48 psfGround snow load (2.3 kPa)
R-50Roof insulation, R-30 walls
SealiftShipped north by sea

How do you build an arctic steel building in Gjoa Haven, Nunavut? You engineer it for the Arctic's snow, wind and cold, insulate it heavily and design every piece to fit the summer sealift. This 73 ft 8 in. x 73 ft 8 in. single-slope storage building was designed to the 2015 National Building Code of Canada for a 48 psf ground snow load, with R-50 roof and R-30 wall insulation. Toro designed, engineered and supplied this arctic steel building for commercial warehousing and storage in Gjoa Haven, on King William Island in Nunavut's Kitikmeot Region.

It is a pre-engineered red iron steel building with multi-span rigid frames, the system our customers choose for warehouses and large storage buildings. Toro has supplied pre-engineered steel buildings for more than 40 years and sold more than 100,000 of them, from Michigan to the far north, and every one is engineered for the snow, wind and seismic loads at its exact site. This arctic steel building shipped with sealed permit and erection drawings and was assembled locally in Gjoa Haven.

Key takeaways

  • Engineered for the Arctic. Designed to the 2015 NBC for a 48 psf ground snow load and a 0.54 kPa 1-in-50 wind pressure on open tundra.
  • Built to hold heat. R-50 roof and R-30 wall insulation under a standing seam roof on high-thermal clips.
  • Designed for the sealift. Steel members limited to 38 ft so the whole kit fits in sea containers, with spare parts included for a remote site.

Arctic steel building specs

The arctic steel building as ordered and engineered.

DetailArctic Steel Building: 73x73 Insulated Storage
LocationGjoa Haven, King William Island, Kitikmeot Region, Nunavut, Canada
BuildingPre-engineered red iron steel building, multi-span rigid frames
Size73 ft 8 in. x 73 ft 8 in.
Floor areaAbout 5,430 sq ft
RoofSingle slope, 17 ft 6 in. high side to 11 ft 6 in. low side
BaysSix bays of about 12 ft 3 in.
FoundationRaised steel platform on a gravel pad (built locally)
UseCommercial warehousing and storage
InsulationR-50 roof, R-30 walls
Roof panel24-gauge standing seam on high-thermal clips with thermal blocks
Wall panel24-gauge PBR
DoorsTwo 10 x 10 ft framed openings, three insulated walk doors with panic hardware
Code2015 National Building Code of Canada
DeliveryShipped north by sealift

Price a building like this

Tell us your size, site and use, and a Toro building consultant will come back with an engineered, code-compliant quote.

Watch: from sealed drawings to the Arctic

This arctic steel building went from sealed engineering drawings to a sealift voyage to a finished building in Gjoa Haven. Watch the whole journey.

This 73 x 73 ft single-slope steel storage building in Gjoa Haven, Nunavut was engineered for extreme cold, heavy snow and relentless wind, then shipped north by sealift. The video goes from the sealed engineering drawings to the finished building.

Arctic steel building in Gjoa Haven, Nunavut in winter, with stairs to the walk door and a skirted raised base
The finished building in winter, raised on its platform with stairs to the walk door.
Overhead door openings on the sidewall of a steel storage building in snowy Gjoa Haven
The sidewall overhead doors after a snowfall.
Finished charcoal gray steel storage building on a gravel pad in Gjoa Haven, Nunavut
The finished building on its gravel pad, with the raised base skirted.
Steel building frame on a raised steel platform above the ground in Gjoa Haven
The frame on the raised steel platform, with air space underneath.
Steel frame going up on a raised platform on a gravel pad in Nunavut, with a telehandler
Erecting the frame on the gravel pad.
Steel building frame at dusk under a pink Arctic sky in Gjoa Haven, Nunavut
The frame complete at dusk.

Design your own building the same way with the free 3D building designer: set the width, length, height, doors, lean-tos, roof pitch, colours and wainscot, then send it to a building consultant for an engineered price.

Want a building like this one?

Send us your size, site and how you will use it, and a building consultant will come back with an engineered quote.

Engineered for Gjoa Haven, Nunavut: the design loads

Gjoa Haven sits on King William Island, north of the Arctic Circle, on open tundra with long, extremely cold winters and strong winds. These are the design criteria for this arctic steel building.

Design criteriaValue
Building code2015 National Building Code of Canada (NBC)
Climatic dataGjoa Haven isn't listed in the NBC climatic tables, so the design used the NBC values for Cambridge Bay, the nearest listed location in the Kitikmeot Region
Ground snow load48.05 psf (2.3 kPa)
Rain on snow2.1 psf (0.1 kPa)
Roof snow load (design)40.5 psf (1.94 kPa), normal exposure
Roof live load20.9 psf (1.0 kPa)
Wind1-in-50-year wind pressure of 11.28 psf (0.54 kPa), open terrain
SeismicLow: Sa(0.2) = 0.163, peak ground acceleration 0.102, site class D (stiff soil)
ImportanceNormal (importance factors 1.0 for snow, wind and seismic)
Collateral load4.5 psf
Base platesKept to 8 in. deep to sit on the wide-flange steel beams of a raised platform foundation
Drawings suppliedSealed anchor rod plan, sealed permit drawings, sealed erection drawings and a sealed letter of certification

See how we engineer every building on our engineering page, or read the National Building Code of Canada 2015. More from Noah Sinclair, our in-house structural engineer.

Get loads engineered for your site

Every quote is engineered for the snow, wind and seismic loads where your building will stand.

Designing an arctic steel building for the sealift

Gjoa Haven has no road. Everything arrives by air or by sea.

Heavy freight reaches Gjoa Haven on the summer sealift, when ships can reach the hamlet. That shaped how this arctic steel building was designed and packed:

  • Steel members limited to 38 ft, so every frame, purlin and girt fits inside a sea container.
  • Remote-site allowances: spare secondary members, cladding, trims, sealants and fasteners, because a missing part can't be picked up locally.
  • Insulation rolls shipped loose so they can be repacked into containers.
  • Materials shipped to a port in Quebec, where they were loaded into containers for the voyage north.
  • Export primer on the structural steel to protect it during a long trip and storage.

Miss the sealift window and a building can wait a full year, so the order, engineering and shipping are planned backwards from the sailing date.

In the Arctic, the ship schedule is part of the engineering. Every member has to fit in a sea container.
Toro engineering, on remote and northern projects

R-50 and R-30: keeping the heat in an arctic steel building

Insulation is the difference between a usable building and a frozen one.

  • R-50 roof insulation (about 15.5 in.) and R-30 wall insulation (about 9.25 in.).
  • A standing seam roof (24-gauge) on high-thermal clips with 3/8 in. thermal blocks, which reduce heat loss through the purlins.
  • 24-gauge PBR wall panels, a heavier gauge than many standard buildings.
  • Three insulated walk doors (R-11.1 leaf) with panic exit hardware, heavy-duty closers with hold-open arms, chain stops, and keys that match.
  • Two 10 x 10 ft framed openings for overhead doors, sized for equipment and freight.

Single slope and multi-span frames for an arctic steel building

A shape that suits snow, wind and shipping.

This arctic steel building uses a single-slope roof that falls from 17 ft 6 in. on the high side to 11 ft 6 in. on the low side, at roughly 1:12. The single slope sends snowmelt to one side and keeps the building's profile low in the wind.

Instead of one long clear span, the 73 ft 8 in. width is carried by multi-span rigid frames with four interior tube columns. Shorter spans keep each steel member under 38 ft for the sea containers and lighter for erection in a remote community. The frames sit in six bays of about 12 ft 3 in., with rod bracing in the roof and sidewalls.

The whole building stands on a raised steel platform built on a gravel pad. The photos show the frame going up on the platform's steel beams and the finished building with its base skirted and stairs up to the walk door.

What to watch for when building in the Arctic

Lessons from engineering buildings for Canada's far north.

  • The sealift calendar. For any arctic steel building, ships reach Arctic communities only in summer, so ordering, engineering and shipping have to be locked in months ahead.
  • Permafrost and foundations. Ground that stays frozen year-round can move if it thaws. This building sits on a raised steel platform above a gravel pad, so cold air can circulate underneath and the building's heat doesn't thaw the ground. Its base plates were kept 8 in. deep to sit on the platform's steel beams.
  • Climatic data. Many Arctic communities aren't listed in the NBC climatic tables, so engineers use the nearest listed location. Confirm the design loads with your building official before you order.
  • Wind-driven snow. Open tundra means high winds and drifting, so doors, closures and trims need to keep snow out.
  • Spare parts. There's no hardware store down the road. Order spares of fasteners, sealants, trims and panels.
  • Building through the cold. Plan erection for the short construction season, and have insulation and doors ready to close the building in fast.
  • Local approvals. Check permit and code requirements with the Government of Nunavut and the hamlet early.
Many Arctic communities aren't in the code's climate tables. Use the nearest listed location, and confirm it with your building official.
Northern design note

Building in the north?

Get a quote engineered for your site's snow, wind and shipping route, within 1 business day.

What does an arctic steel building cost?

Starting prices, and what moves them in the north.

New Toro steel building kits start at $26 per sq ft (CAD) in Canada and $19 per sq ft (USD) in the United States, and every building is quoted to meet the loads and codes for your location and use. For an arctic steel building, the biggest price drivers are:

  • Snow and wind loads. Arctic loads need heavier framing than most southern sites.
  • Insulation. R-50 roofs and R-30 walls add material and cost, and save on heating every winter after.
  • Shipping. Sea containers, ocean freight, port handling and remote-site spares are a real part of the budget.
  • Doors and openings, especially insulated and wind-rated doors.
  • Building size and shape.

The building kit doesn't include the foundation, erection, containers or ocean freight, so budget for those separately. See our steel building sizes page and our Canadian steel building prices guide.

Need a building sooner, or for less?

New, unused clearance buildings from cancelled orders are engineered for your site like any Toro building.

Why northern builders choose Toro

More than 40 years and 100,000+ buildings.

  • More than 40 years supplying pre-engineered steel buildings, with more than 100,000 buildings sold.
  • In-house engineering, with every building designed for the snow, wind and seismic loads at its exact site and shipped with engineer-stamped drawings.
  • Experience with remote sites, from Northern Ontario to the Yukon and Nunavut, including sealift packing and spare-parts planning for every arctic steel building.
  • Precision laser-cut components that arrive ready to bolt together, for 30 to 50% faster construction than conventional wood framing.
  • A 25 to 40-year paint warranty on straight-wall buildings, depending on panel and finish.
  • Canadian offices in Markham and Oshawa, with building specialists who speak English, French, Spanish, Portuguese, Italian, Persian and Chinese.

Start your quote

Tell us your size, site and use, and get a free quote engineered for your loads and code.

How this building came together

Toro engineers and supplies the kit; the owner's team builds it.

1

Specification and 3D design

Toro and the owner

Size, single-slope roof, insulation and doors set for Arctic storage.

2

Engineering

Toro

The arctic steel building designed to the 2015 NBC, with sealed permit and erection drawings.

3

Port and sealift

Toro ships to port, owner loads containers

Members kept under 38 ft and loaded into sea containers for the summer sealift.

4

Platform foundation

Owner or contractor

A raised steel platform built on a gravel pad, sized to the sealed column reactions.

5

Assembly

Owner or contractor

Frames, panels and insulation bolted together in Gjoa Haven. Toro doesn't install.

The building consultant who sold this building

Every Toro building has one consultant from first call to delivery.

Nick Levy

Building Consultant · Toro Steel Buildings

Nick Levy sold this arctic steel building and worked through the specifications, engineering, insulation and sealift requirements with the owner's team. He has been with Toro since 2002 and helps customers across Canada and the U.S. plan buildings from garages to large commercial shops.

See Nick's projects and work with Nick

789Buildings sold
24Years at Toro

More buildings Nick Levy has sold

Talk to Nick about your building

Get an engineered quote for your size, site and loads, ask about new and unlisted clearance inventory, or see Nick's past projects.

Arctic steel building FAQs

Still planning your build? Price your building and a building consultant will walk you through it.

Can you build a steel building in the Arctic?

Yes. A steel building can be engineered for Arctic snow, wind and cold and shipped north by sealift. This 73 ft 8 in. x 73 ft 8 in. storage building in Gjoa Haven, Nunavut was designed to the 2015 National Building Code of Canada for a 48 psf ground snow load, with R-50 roof and R-30 wall insulation.

What snow load is a steel building designed for in Nunavut?

This Gjoa Haven building was designed for a ground snow load of 48.05 psf (2.3 kPa) and a roof snow load of 40.5 psf (1.94 kPa). Gjoa Haven isn't in the NBC climatic tables, so the values for Cambridge Bay were used. Every Toro building is engineered for its own site.

How do you ship a steel building to Nunavut?

Heavy freight reaches most Nunavut communities on the summer sealift. This building was designed with every steel member 38 ft or shorter so it fits in sea containers, and it was shipped to a Quebec port to be loaded for the voyage north, with spare fasteners, trims and panels included.

How much insulation does an arctic steel building need?

This building uses R-50 insulation in the roof and R-30 in the walls, with high-thermal standing seam roof clips and thermal blocks to cut heat loss through the framing. Insulated walk doors (R-11.1) help keep heat in.

How much does an arctic steel building cost?

New Toro steel building kits start at $26 per sq ft (CAD) in Canada and $19 per sq ft (USD) in the United States, and every building is quoted to meet the loads and codes for your location and use. In the north, snow and wind loads, insulation, doors and shipping by sealift have the biggest effect on the total cost.

What foundation does a steel building need on permafrost?

In Gjoa Haven, this building sits on a raised steel platform built on a gravel pad, so cold air circulates underneath and the building's heat doesn't thaw the permafrost. The platform is designed locally using the column reactions on the sealed drawings, and the base plates were kept 8 in. deep to sit on its wide-flange steel beams.

Why use a single-slope roof in the Arctic?

A single-slope roof sends snowmelt to one side and keeps the building's profile low in the wind. This one falls from 17 ft 6 in. to 11 ft 6 in. at about 1:12, under a standing seam roof.

How long does it take to get an arctic steel building?

Delivery of a Toro building kit usually takes 2 to 8 weeks to the port, but in the Arctic the sealift schedule sets the real timeline. Plan your order months ahead of the sailing date, and plan erection for the short construction season.

Written by Noah Sinclair, Toro's in-house structural engineer. Every Toro building is engineered for your site's snow, wind and seismic loads and comes with engineer-stamped drawings. Toro has supplied pre-engineered steel buildings for more than 40 years and sold more than 100,000 buildings.

Follow Toro

Keep reading

Browse all articles

Planning a building in the north?

Toro Steel Buildings engineers your kit for your site's snow, wind and shipping route, with a quote within 1 business day.

Join 100,000+ customers who built with Toro

Tell us your size, location and how you'll use the building. A Toro building consultant will come back with an engineered, code-compliant quote within 1 business day. Prefer to talk? Call 1-888-995-3432, or browse in-stock clearance buildings at reduced prices.